Tag Archives: browns bicycles

No bicycle discomfort is as debilitating as back pain. Luckily, back pain is usually caused by a few, simple to fix issues.

Searching for back pain causes and finding a solution biking

by John Brown

Over the past quarter-century, I have helped many riders get going on their bikes without back pain. I’ve been lucky to see the life-changing power of proper posture while riding a bicycle. I have also seen riders walk away from cycling due to simple discomforts and not understanding why. No discomfort is as debilitating as back pain. Luckily, back pain is usually caused by a few easy-fix issues. These issues manifest themselves in lower back pain and upper back pain. See more on some causes and simple fixes to enjoy cycling again.

Lower back pain

The sky-high seat rider can result in back pain.

The #1 cause of lower back pain is saddle height. Not only is this problem every day and painful but also easily fixed. Many riders will raise their saddle too high while trying to get a more efficient pedal stroke. If your saddle is too high, you will tilt your hips at the bottom of each pedal stroke, trying to reach the pedals. That tilting forces the tiny muscles in your back to do the job that the vast muscles in your leg should be doing. To find a proper saddle height check out our bike setup article, or visit your local shop for a bike fit.

The shocking truth

Another frequent cause of lower back discomfort is road shock. While riding, it is typical for minor imperfections in the road to send vibrations through the bicycle and into your body. After some time, this constant vibration can fatigue the muscles in your back. There are a few quick fixes for this problem. The first and most straightforward solution is tire pressure. Rather than maxing out your tire’s pressure, lower the tire pressure in 5 psi increments until you find a force that works for you. Another quick way to squelch road vibration is by adding a suspension seat post. A suspension seat posts absorb the shock before it gets to you.

How is your reach?

Finally, the last common cause of lower back discomfort is your reach. If the distance from your seat to the bars is too great, you begin relying on small muscles in your lower back to support the weight of your upper body instead of your core and arms. Look into having your bike properly fit at a local shop or follow our simple fit guide.

Upper Back Pain

Shrugging off your responsibilities

The leading cause of upper back pain is the riding position, specifically shoulder shrugging. In my experience, many riders don’t know they lift their shoulders when riding. It is just a nervous habit they formed somewhere along the way. Paying attention to where your shoulders are located will help you relax them, alleviating pain.

Additionally, try moving your hands to different positions on the bars. That change in grip does wonders to rest other muscle groups. Sometimes, a proper bike fit is needed to remedy shrugged shoulders, so if the problem persists, visit your local shop for a fitting.

Don’t become a pack mule.

Be careful how much weight you carry on your shoulders. Riding with a backpack is a great way to take what you need, but be careful not to overdo it. If you use a pack to commute, try leaving heavier items like shoes at work. If you need to carry a lot of weight, install a rack with panniers and move that weight onto your bike frame and off your body.

Keep on going

As stated, I have seen riders get off their bikes forever due to discomfort. It’s always sad to see, mainly because I know that simple adjustments can likely eliminate most cyclists’ pain. Be vigilant about removing discomfort. After all, minor aches today can manifest into serious problems later. Find a bike-fitting professional you feel comfortable with and talk about your issues. Your back will thank you.

About John Brown, the author

John operates Browns Bicycle in Richfield, MN as a lifelong cyclist and consummate tinkerer. It all started for him in grade school when the bike bug bit and the fever still existed. Now, and over the past thirty years, he has worked at every level in the bike industry. He is starting, like most, sweeping floors and learning anything he can about bikes. He eventually graduated as a service manager and then as a store manager. Through the years, he has spent extensive time designing and sourcing bicycles and parts for some of the largest bike companies in the world. All the while focusing on helping as many people as possible enjoy the love of riding a bike. In that pursuit, he has taught classes (both scheduled and impromptu) on all things bikes. John also believes in helping every rider attain their optimal fit on the cycle of their dreams. Please feel free to stop in any time and talk about bikes, fit, and parts or share your latest ride. You can also see more of John’s tricks and tips on the Brown Bicycle Facebook Page.
If you are looking for a gently used bike in the south Twin City Metro, you may be in luck if you are in town on Saturday, May 11th.

Bicycle maintenance will keep your bike in optimal condition

by John Brown

Like any other mechanical device, routine bicycle maintenance and cleaning will keep your bike in optimal condition as the season progresses. Additionally, routine bicycle maintenance will make your bike safer to ride when you need it. Where do you start? What do you use? Well, here are a few tips to put you on the right track!

Tip 1: For optimal bicycle maintenance, stay away from the hose

Bike running smooth hose and bucket
Angry hose and happy bucket

Every moving part on your bicycle needs lubrication to stay in optimal condition. The pressure of water coming from a hose will force water into areas that need to be lubricated. The water will displace grease and leave your bicycle susceptible to corrosion and excess wear. Instead of a hose, fill a bucket with warm, soapy water (Dawn dish detergent works well) and use a large sponge to clean all the parts of your bicycle. Rinse all the soap and gunk off with fresh water, and let the bicycle air dry.

Tip 2: Focusing on the drivetrain

If you have a particularly dirty drivetrain* and want to get it clean, you will need the following:Bike running smooth supplies

• Degreaser
• A stiff-bristled brush
• Rubber gloves
• Protective eyewear

 

*(the gears, chain, and the little pulley wheels on your derailleur)

  • First: Start by applying a liberal amount of degreaser to the chain, gears, and derailleur pulleys. Also, pay close attention not to direct the degreaser toward the center of either gear set. Doing so will drive the degreaser into bearings that need to remain lubricated.
  • Second: Once well saturated, begin freeing up dirt and debris by scrubbing back and forth with the stiff-bristled brush.
  • Third: After you have broken up all the contaminants, rinse the drivetrain with a warm soap/water solution.

Tip 3: reapply lubricant

Most areas of a bicycle are protected from the elements with rubber seals. Those rubber seals do a good job of keeping lubricants where they are supposed to be. Furthermore, it also means that the only bicycle areas that can be lubricated without disassembly are the chain and cables.

Lubricating the chain

bicycle maintenance
Proper lubrication is essential to keep your bike in optimal condition.
  • First: To lube the chain, prop your bicycle up so you can freely backpedal. While backpedaling, coat the chain evenly with a lubricant like in the image above.
  • Second: Fold a rag around the chain between the lowest pully and the chainrings. Next, backpedal with your right hand while holding the rag in place with your left. You want to try and remove all the excess lubricant you can. When complete, the chain will feel almost dry to the touch, and that’s OK. Even though the outside of the chain seems under-lubricated, there is still ample lubricant between the chain’s links and within the rollers.

Lubricating the cables

If shifting of braking feels rough at the lever, you may need to lube the cables. Here’s how to do that:

  • First: Apply lubricant in small doses where the cable enters the housing (see below).
  • Second: Cycle the gears, or squeeze the brakes until capillary action draws the lube into the cable housing.

bicycle maintenance

Ensuring your bicycle is clean and properly lubricated is essential to make sure your bike is in optimal condition.

About John Brown, the author

As a lifelong cyclist and consummate tinkerer, John operates Browns Bicycle in Richfield, MN. It all started for him in grade school when the bike bug bit and that particular fever is still there. Now, and over the past thirty years, he has worked at every level in the bike industry. Started, like most, sweeping floors and learning anything he could about bikes. He eventually graduated as a service manager and then store manager.  Through the years, he has spent extensive time designing and sourcing bicycles and parts for some of the largest bike companies in the world. All the while focusing on helping as many people as possible enjoy the love of riding a bike. In that pursuit, he has taught classes (both scheduled and impromptu) on all things bikes. John also believes in helping every rider attain their optimal fit on the bike of their dreams. Please feel free to stop in any time and talk about bikes, fit, and parts, or share your latest ride. You can also see more of John’s tricks and tips on the Brown Bicycle Facebook Page.
Brown's Bicycles service area/teaching center

HaveFunBiking’s product editor has opened Brown’s Bicycles!

Over the past two years HaveFunBiking (HFB) readers have enjoyed reading many product reviews, how-to articles and helpful tips by John Brown. Now, John has opened a bike shop of his very own, called Brown’s Bicycles. Located a few miles west of HFB, the shop is at 2323 W 66th Street, right here in Richfield Minnesota. Don’t worry, he will still be contributing to the HaveFunBiking blog, but this new development gives our HFB readers the chance to continue learning about bicycles through print as well as face to face!

Brown’s Bicycles continues to educate

John has designed the layout of Brown’s Bicycles specifically to continue educating riders about the joys of all things bike. The open service area is purposefully modeled to operate as a functioning repair area as well as classroom.

A full service bike shop!

While Brown’s Bicycles is founded on the concept of educating riders, they still offer a complete line of new bicycles from Giant, and Jamis as well as a rotating stock of used bicycles. If you need accessories or parts, Brown’s Bicycles offers a curated selection of the best products available. If they don’t have what you need in stock, your special orders are usually available within 24 hours.

As a thank you to the HFB readers, Brown’s Bicycles is offering a tune up special! Mention HaveFunBiking for $20 off your next Basic Tune Up or $25 off a Deluxe Tune Up until June 15th. Additionally, in at stop the new shop for a Richfield bike map not found in the 2018 Minnesota Bike/Hike guide!